Snow Sprays Automatic Aerosol Filling Machine / Aerosol Can Filling
Machine Introductions for Every Part:
CJXH-2800B automatic aerosol filling line includes aerosol can arranging
machine, liquid filling machine, valve inserting machine, crimping
and propellant gas filling machine, actuator pressing machine, cap
pressing machine, and packing table.
Can arranging machine has nine flat-roofed stainless conveyor belts, it is used to
automatically arrange cans and feed the filling line on the
stainless conveyor belt, can load 200-400 pcs cans. It is equipped
with an explosion-proof motor and switch.
Liquid filling machine has four liquid material fillers with four liquid metering
cylinders, the upper one of liquid metering cylinder is a piston,
below cylinder is containing liquid materials, the liquid material
is sucked up automatically from the barrels to cylinders. Then the
liquid material will be filled 4 times equally into an aerosol can
through the rotary table.
Valve inserting machine consists of a valve arranging turntable, a valve blowing part and
a valve inserting part. Putting valves into the rotation manually.
In the rotation, the valves are thrown into the slot, then through
the blowing part the valves come to the inserting part.
Valve correcting device, crimping and propellant gas filling machine:
in last step, the valve was inserted into the can, but normally the
valves will jump out of the can opening and be away from the
opening center, then here is the valve correcting device, it is
used to correct valves, make it straight, set it right and press it
into can opening, like this.
After this, there is crimping machine, it is used to seal the valve
with internal expanding mode.
Then three gas fillers, the gas will also be filled 3 times equally
into an aerosol can. Behind the gas fillers, there are three gas
metering cylinders, upper one is a piston cylinder, below one is
for containing propellant gases, such as LPG, butane, propane, or
Automatic can weighing machine is with stable and highly sensitive weighing sensor, a signal
acquisition instrument, and PLC programmed control. By setting a
range value of weight, substandard spray cans will be picked up
automatically, which make sure all cans’ weight are in this range.
Automatic water bath leakage testing machine is used to test if there is any air leakage for the finished
product. It puts gas filled products into water tanks automatically
and control the water temperature at 55 degree centigrade by
electrical heating or steam heating for 3 minutes. If no bubbling
in the warm water after 3 minutes, in general, the aerosol products
will not leak within two years.
Actuator pressing machine is used to press the actuators, it consists of vibrating plate,
actuator presser, and a rotary table. During Vibration the
actuators come down to the cans, and then be pressed here by the
actuator presser, through the rotary table, cans continue to move
Cap pressing machine is very same with actuator pressing machine, it is used to press
the caps, it consists of vibrating plate, cap presser, and a rotary
table. During Vibration the caps come down to the cans, and then be
pressed here by the cap presser, through the rotary table, cans
will move along.
Packing table automatic aerosol filling line usually uses stainless conveyor
belts with 13.5m, including this packing table with 2.5m. At here,
just take the finished aerosol cans to your cartons. The packing
table is also equipped with an explosion-proof motor.
|Outline (L*W*H) (mm)||18000*1800*1900|
|Liquid fill (ml)||50-1000(customized)|
|Gas fill (ml)||20-700(customized)|
|Repeated filling accuracy||1%|
|Diameter of cans (mm)||35-65(customized)|
|Height of aerosol can (mm)||80-350(customized)|
|Valve (mm)||25.4(1 inch)|
|Working pressure (MPa)||0.65-1|
|Max. gas consumption (m3/min)||5.5|